What voltage can water-based fire suppressants safely handle?

Most water-based fire suppressants are rated safe for use on electrical equipment up to 1,000 volts, provided they are applied from a safe distance using an appropriate nozzle. Some specialist formulations extend that rating further, but 1,000 V is the widely accepted ceiling for standard water-based agents in professional fire safety applications. The limit exists because water conducts electricity, and any conductive path between the suppression agent and the operator creates a risk of electric shock. The sections below explain how that limit is determined, where Hydrogel fits, and what it means for lithium-ion battery fires.

At what voltage does water become dangerous to use on fires?

Water becomes hazardous as a fire suppressant at voltages above 1,000 volts under standard conditions. Below that threshold, water can be used on live electrical equipment when applied correctly. That means a minimum safe distance and a nozzle that breaks the stream into a fine spray rather than a solid jet. Above 1,000 V, the conductivity of water creates an unacceptable risk of electric shock or flashover travelling back through the stream to the operator.

The danger is electrical conductivity. Pure water is a poor conductor, but tap water and mixed suppression agents contain dissolved minerals and additives that make them conductive enough to carry current. A solid jet aimed at live equipment above 1,000 V can create a direct conductive path between the high-voltage source and whoever is holding the hose.

Safe-distance requirements also matter. Even within the 1,000 V limit, fire safety standards specify minimum standoff distances, typically at least one metre for spray application. Closing that gap or switching to a solid stream increases the risk significantly, regardless of voltage. Voltage rating alone does not determine safety. Application technique, nozzle type and distance all interact with the voltage limit. Verify each of them before using a water-based agent near energised equipment.

How do dielectric properties affect fire suppressant safety ratings?

A suppression agent’s dielectric strength, its ability to resist electrical current, is the primary factor in its safety rating for use near live electrical equipment. Agents with high dielectric strength do not readily conduct electricity, so they can be applied closer to energised equipment with lower shock risk. Agents with low dielectric strength conduct current more easily. They must be used from a greater distance or avoided near live equipment entirely.

Testing bodies measure dielectric properties by passing a known voltage through a sample of the agent and measuring how much current flows. The lower the current, the higher the dielectric rating. This is why CO2 and dry powder extinguishers traditionally carry high electrical safety ratings: neither conducts electricity in the way that water-based agents do.

For water-based agents, dielectric performance depends heavily on what is dissolved or suspended in the water. Plain water with a low mineral content has a higher dielectric strength than water mixed with ionic additives. The modified clay in Hydrogel affects conductivity differently from the surfactants found in conventional foams, so its electrical profile needs to be assessed on its own test evidence rather than assumed from its water content.

Certification bodies test suppression agents against standardised dielectric protocols before assigning a voltage rating. A rated voltage ceiling is therefore a tested and documented specification, not a general guideline. When evaluating any fire suppression system for use near electrical equipment, confirm the certified rating, the specific product it applies to and the conditions of the test. Do not rely on assumptions based on the agent’s appearance or water content.

See where Hydrogel fits your fire-safety strategy
From lithium-ion batteries to existing water-based suppression systems, speak with Anogas about your application.

Discuss your application

How does Hydrogel behave on electrical fires compared with plain water?

Hydrogel is a water-based agent containing modified natural clay. It cools hot surfaces, and its viscosity responds to heat. The agent thickens on contact with a hot surface, which is intended to keep it in contact with that surface rather than running off. Despite being more than 95% water, Hydrogel can be used on electrical equipment up to 1,000 volts when applied with suitable nozzle configurations.

This behaviour matters for electrical safety. A solid jet of water maintains an unbroken liquid column that can carry current back towards the nozzle. A gel that breaks up and clings to surfaces is less likely to sustain that column. Nozzle choice, distance and the voltage present still determine whether application is safe.

Adhesion also affects how much agent is needed. Because Hydrogel stays on hot surfaces longer than water, a given cooling effect may need less agent. That can mean shorter application bursts, less liquid introduced into an energised environment and less pooling around electrical infrastructure. Less runoff also means less contaminated water to manage afterwards, which is relevant in industrial settings where electrical equipment and drainage systems are close together.

When comparing agents, assess the tested voltage rating, the nozzle and discharge arrangement, and the runoff to be managed. Hydrogel is PFAS-free, which is relevant where runoff and environmental compliance are concerns. That is a separate question from electrical safety and firefighting performance. See how Hydrogel works for the mechanism in more detail.

Which fire classes involve electrical equipment, and how are they handled?

Electrical fires are not assigned their own fire class in the European classification system. Electrical involvement is treated as a hazard condition that overlaps with other fire classes, most commonly Class A (solid combustibles) and Class B (flammable liquids). The relevant European standard uses a lightning bolt symbol to indicate that an extinguisher has passed dielectric testing and is suitable for use near live electrical equipment. This is a safety designation, not a fire class.

When electrical equipment is involved in a fire, the fire class is determined by what is burning: the insulation, the casing or the surrounding materials. The electrical hazard designation tells responders whether a given agent can be applied without shock risk. A fire in an electrical cabinet might be a Class A fire involving burning plastic. The choice of extinguisher then depends on both the fire class and the voltage present.

Lithium-ion battery fires do not map cleanly onto traditional fire classes. Burning cells involve solid materials, flammable gases and reactive chemistry that can sustain thermal runaway independently of an external oxygen supply. Standard fire class designations were not designed around this behaviour. Specialist agents tested for lithium-ion battery applications, such as those tested to KIWA NTA 8133, are therefore relevant alongside class-based selection.

Should water-based suppressants ever be used on lithium-ion battery fires?

Water-based agents can play a role, but only where the agent and the application are suited to lithium-ion battery fires. Plain water is not a reliable answer on its own. Cooling the exterior of a battery pack may reduce surface temperature while heating continues inside, and reignition can follow once cooling stops.

The central point is that suppressing visible flames is not the same as stabilising the battery. When a cell enters thermal runaway, internal materials decompose and flammable and toxic gases are released, including hydrogen, methane and hydrogen fluoride. Heat from one failing cell can pass to neighbouring cells. Temperatures during thermal runaway can reach between 850 and 1,500 degrees Celsius. Extinguishing the flames does not necessarily end internal heating, gas release or the risk of reignition.

This is where Hydrogel differs from plain water. It combines surface cooling with a heat-responsive gel that stays in contact with hot battery surfaces. This helps limit heat transfer to adjacent cells. How far any externally applied agent reaches depends on access to the cells, the battery configuration, the enclosure design and how the agent is delivered. Do not assume it reaches cells inside an enclosed pack or stops every internal reaction.

Hydrogel has been tested to KIWA NTA 8133 for lithium-ion battery fire applications. That result relates to the specific extinguisher model and test scope. It is not approval for every battery size, installation or marine application. Verify the certificate, the model it covers and its limitations before relying on it. Hydrogel is supplied as a ready-to-use premix that needs no on-site dilution, and it contains no intentionally added PFAS. That matters as European PFAS restrictions tighten towards the 2031 deadline under Regulation (EU) 2025/1988, but it is a separate claim from firefighting performance.

After any battery fire, plan for the post-fire period. Residual heat, gas hazards and the risk of reignition can persist after the flames are out. Monitor the battery, restrict access and contain runoff. Do not treat extinguishment as proof that a battery is safe to reuse, store, transport or dispose of. Hydrogel Shield is a separate product intended for longer-term containment to help prevent reignition of damaged or extinguished batteries.

For a handheld first response in warehouses, EV charging areas, recycling facilities or industrial settings, assess portable extinguishers using Hydrogel against the battery type, the voltage present and the certified test scope. For larger installations, check the complete setup before specifying anything: access to the battery, enclosure design, agent quantity, nozzle and discharge arrangement, coverage, temperature range and required approvals. Do not assume an existing water-based system will work with Hydrogel without engineering checks. Those assessing Hydrogel as a thermal runaway blocker should compare its cooling, thermal isolation and gas-suppression claims with the evidence for their specific battery configuration.

Gerelateerde artikelen

Harry Verbakel