What Makes Hydrogel Suitable for Electric Vehicle Fire Suppression

Electric vehicle fires present a challenge that conventional fire suppression was not designed to solve. As lithium-ion batteries power a growing range of vehicles, energy storage systems and industrial equipment, the fire risks associated with them have become more urgent and more complex. Anyone responsible for fire safety planning where EV battery fire risk exists needs to understand two things: why standard extinguishing agents can fall short, and what Hydrogel fire suppression can and cannot do.

This article examines the science behind EV battery fires, explains how Hydrogel’s mechanism addresses those specific risks, and outlines the environments where this approach to lithium-ion battery fire suppression offers practical advantages. It also covers the limits of any externally applied agent and the checks needed before choosing a firefighting setup.

Why Lithium-Ion Battery Fires Are Difficult to Suppress

Lithium-ion battery fires differ from most fire types because the energy source is inside the burning material. When a cell enters thermal runaway, a self-sustaining chain reaction generates heat and flammable gases from within the cell. Oxygen may also be released from some cell chemistries. The fire cannot simply be starved of oxygen or cooled at the surface in the way a conventional Class A or B fire can.

This means extinguishing visible flames is not the same as stabilising the battery. A battery can keep heating internally, release gas and re-ignite after the flames have been put out. Effective suppression therefore has two aims: control the flames, then remove enough heat to stop the reaction spreading from cell to cell.

Each conventional agent has strengths and limits. Water is an effective coolant, but its low viscosity means it can run off hot surfaces quickly, which limits sustained contact with the heat source. CO2 and dry chemical agents can knock down flames but provide little cooling, so internal temperatures may stay high enough to allow re-ignition or propagation to adjacent cells. Foam agents are formulated mainly for hydrocarbon fires rather than the behaviour of failing battery cells. How well any of these perform also depends on whether the agent can reach the affected cells, which in an enclosed pack it often cannot.

See where Hydrogel fits your fire-safety strategy
From lithium-ion batteries to existing water-based suppression systems, speak with Anogas about your application.

Discuss your application

How Hydrogel’s Heat-Responsive Viscosity Helps Against EV Fires

Hydrogel is a water-based agent containing modified natural clay. At ambient temperature it behaves as a low-viscosity fluid that can be applied through suitable nozzle configurations. On contact with hot surfaces, its viscosity increases, and it is designed to form an adhesive layer that stays in contact with the surface instead of running off.

This matters in a lithium-ion battery fire because sustained contact improves heat extraction compared with water alone. The clay component also acts as a physical barrier at the surface, which can help limit the spread of heat to neighbouring cells or modules. The practical result is faster cooling and a lower risk of re-ignition where the agent reaches the affected surfaces.

Reach is the key qualification. An externally applied agent does not necessarily reach cells inside a sealed pack, and it cannot be assumed to stop every internal reaction. Performance depends on access to the battery, enclosure design, battery configuration, agent quantity and delivery. Hydrogel does not guarantee that re-ignition will be prevented.

Because Hydrogel stays on hot surfaces for longer, less agent may be needed to achieve effective cooling than with water alone, depending on the scenario. In enclosed environments such as car parks or cargo holds, a smaller volume of agent can also mean less contaminated runoff to manage afterwards. For a detailed explanation of the mechanism, how Hydrogel works covers the science behind gel formation and its fire suppression properties.

Which Product Does What

Anogas products have distinct roles, and they should not be treated as interchangeable.

  • Hydrogel: cooling and initial fire suppression.
  • Hydrogel Shield: longer-term containment, intended to help prevent re-ignition of damaged or extinguished batteries.
  • Hydrogel SubZ: a frost-protected formulation for relevant cold-temperature applications.

Compatibility with Existing Water-Based Fire Suppression Systems

Facilities evaluating new suppression agents need to consider infrastructure compatibility. Replacing or retrofitting systems is expensive and disruptive, so agent interchangeability can significantly affect adoption decisions.

Hydrogel is designed to be interchangeable with water in water-based fire suppression systems. Whether a specific installation can use it without modification still depends on the complete setup: nozzle and discharge arrangement, coverage, operating temperature, agent quantity and any required approvals. Do not assume an existing sprinkler system will work with Hydrogel. Confirm compatibility through an engineering assessment, and obtain the relevant approvals before changing any system. Mandatory fire protection requirements, particularly in marine settings, must continue to be met.

The same principle applies to handheld fire extinguishers, where Hydrogel can be used in portable units in place of water-based agents. When reviewing test evidence, identify the specific extinguisher model, test standard and scope. A portable-extinguisher test result does not extend to every model, battery size or installed system.

Electrical safety is a further consideration. Although Hydrogel is over 95% water by composition, it can be applied to electrical equipment up to 1,000 V when used with appropriate nozzle configurations. This is relevant in EV charging and energy storage environments where live equipment may be present during a fire.

PFAS-Free Composition and the Regulatory Landscape

Regulation of fire suppression agents is tightening across Europe and other major markets. PFAS, the group of synthetic fluorinated compounds historically used in many foam agents, face wide-ranging restrictions because of their environmental persistence and toxicity. For facilities and distributors selecting products, PFAS compliance is a baseline requirement in a growing number of jurisdictions.

Hydrogel contains no intentionally added PFAS. Analysis using highly sensitive methods shows PFAS below 1 ppb. This is an analytical result and should be read as such: it is not proof of absolute absence. It is well below regulatory thresholds and supports compliance as restrictions broaden. PFAS-free status is a separate claim from firefighting performance, wider environmental safety or marine approval, and should not be used to support those claims.

Aquatic toxicity studies carried out to OECD guidelines indicate that Hydrogel is non-toxic to algae and daphnia. After a service life of more than ten years, it is expected to be recyclable as a compost-enrichment supplement. The Hydrogel product overview covers its classification, certifications and environmental data in detail.

See where Hydrogel fits your fire-safety strategy
From lithium-ion batteries to existing water-based suppression systems, speak with Anogas about your application.

Discuss your application

Application Environments Where Hydrogel Can Help

The growth of electric vehicles and battery-dependent systems has spread lithium-ion fire risk across many environments, several of which were not designed with this hazard in mind. Effective EV fire suppression requires solutions that can be deployed in these varied settings, often within existing infrastructure.

  • Parking structures and EV charging facilities: Underground and multi-storey car parks concentrate EV fire risk in enclosed spaces with limited ventilation. Sustained cooling is particularly relevant where thermal runaway in one vehicle can spread to adjacent ones.
  • Warehousing and logistics: Facilities storing or handling e-bikes, battery packs, power tools and portable electronics face growing exposure. Where an assessment confirms compatibility, Hydrogel may allow sites to improve suppression capability without replacing their systems.
  • Maritime environments: Vessels carrying electric vehicles or battery cargo face severe consequences from onboard fires. Marine use involves flag-state requirements, class rules and marine equipment approvals, which are separate from portable-extinguisher test results. Verify the certification status of any product, and distinguish passed tests, pending certification and granted approval.
  • Recycling facilities: Electronic waste contains lithium-ion batteries in various states of damage, creating unpredictable fire risk. Cooling and flame suppression can help control fires in these environments, but damaged batteries need continued monitoring after the fire is out.
  • Industrial energy storage: Grid-scale and facility-level battery storage is a high-value, high-consequence application. Agent performance depends on enclosure design, access to the cells, discharge arrangement and agent quantity, so assess the whole firefighting setup instead of the agent alone.

Any figures for extinguisher capacity, operating temperature or monitoring duration apply to the application they were derived from. Treat them as examples unless a reliable source establishes wider validity.

After the Fire

Putting out the flames does not end the hazard. Residual heat, gas release and the risk of re-ignition can continue after a lithium-ion battery fire appears to be under control. Monitor the battery, restrict access and handle it safely. Extinguishment does not mean the battery is safe to reuse, store, transport or dispose of. Hydrogel Shield is intended to support longer-term containment of damaged or extinguished batteries.

The underlying challenge is the same across all of these environments: a fire driven by internal electrochemical energy that no single agent controls in every case. Hydrogel’s heat-responsive viscosity, cooling action and compatibility with water-based equipment make it a practical option within a wider fire-safety response. To assess how to build this capability into a facility, fixed fire suppression systems using Hydrogel offer a scalable route from portable extinguishers to building-level protection, subject to engineering and approval checks.

Related Articles

Harry Verbakel