What causes re-ignition in battery fires and how do you prevent it?

Re-ignition in lithium-ion battery fires happens because cells can retain heat and chemical energy long after visible flames disappear. A battery in thermal runaway continues to generate heat internally, so extinguishing the flames does not necessarily end the fire. The sections below cover why this happens, how long the risk can persist, and which suppression approaches address it.

Why do lithium-ion batteries reignite after being extinguished?

Lithium-ion batteries can reignite after being extinguished because the energy driving the fire comes from chemical reactions inside the cells, not from an external fuel source. Suppressing visible flames removes the flame but can leave internal heat and reactive chemistry largely intact. While that heat and chemistry remain, re-ignition is a real risk.

When a cell fails, it can enter a self-sustaining chain reaction called thermal runaway. Internal materials decompose and release flammable gases, including hydrogen and methane. The heat from one failing cell can transfer to neighbouring cells. Even after responders believe the fire is out, adjacent cells may still be absorbing heat and approaching their own failure threshold. The fire can restart minutes or hours later, often without any external ignition source.

Gas release is a second factor. Lithium-ion battery fires produce hydrogen fluoride and other gases that can keep escaping from the battery after the flames are gone. These gases are toxic, and some are flammable. If they accumulate near a heat source, they can create the conditions for re-ignition without any additional fuel.

This is why thermal runaway management needs more than flame suppression. Flame suppression and battery stabilisation are different outcomes. Stabilisation depends on sustained cooling, control of gas release, and monitoring afterwards.

What is thermal runaway and how does it drive re-ignition?

Thermal runaway is a self-reinforcing cycle of heat generation inside a lithium-ion cell. Rising temperature triggers chemical decomposition, which releases more heat and accelerates further decomposition. Mechanical damage, overcharging, overheating, or manufacturing defects can start it. Once it is under way, it is difficult to interrupt from the outside.

The link to re-ignition is direct. During thermal runaway, internal temperatures can rise well above the ignition point of the gases being released. External cooling may lower the surface temperature, but the internal reaction can still be producing heat. If that heat exceeds the cooling applied, or reaches a neighbouring cell, the conditions for re-ignition return.

Thermal propagation makes this worse. Heat passes through the pack to adjacent cells, which then begin their own thermal runaway. A fire that appears contained can therefore restart in another part of the same battery system. Effective suppression needs to slow or interrupt this propagation, not only cool the surface of the cell that is burning.

Water provides effective initial cooling, but it runs off hot surfaces quickly and, applied in short bursts, may not give sustained cooling. Agents that stay in contact with hot surfaces are better suited to this problem. Hydrogel is a water-based agent containing modified natural clay. Its viscosity increases in response to heat, which is intended to keep cooling material on hot battery surfaces rather than letting it drain away. You can read more about the mechanism behind Hydrogel. As with any externally applied agent, its effect depends on whether it can reach the heat source.

See where Hydrogel fits your fire-safety strategy
From lithium-ion batteries to existing water-based suppression systems, speak with Anogas about your application.

Discuss your application

How long can a battery fire re-ignite after it appears out?

There is no universal re-ignition window. A lithium-ion battery fire can reignite at least 20 minutes after visible flames are extinguished, and in larger systems the risk can persist for hours. Industry guidance commonly recommends monitoring for a minimum of 20 minutes after apparent extinguishment, and a cooling period of 48 hours before a battery is considered for disposal. Treat these figures as minimums to check against the battery, the application, and the guidance that applies to it.

The window depends on the size and capacity of the battery, the extent of cell damage, the ambient temperature, and the suppression agent used. A small, fully cooled phone battery presents a much shorter risk window than an energy storage system or an electric vehicle pack, where heat can persist deep inside the structure after the exterior has cooled.

Post-incident monitoring is part of managing the risk. Once a battery appears stable, move it to a water-filled containment vessel or a well-ventilated outdoor area, isolated from combustible materials. Hissing or sizzling indicates continuing gas release and possible instability. A battery can be considered stabilised only when flames have stopped, no new flame eruptions occur, and gas emissions have ceased. Continue to observe it after that. Do not equate extinguishment with safe reuse, storage, transport, or disposal.

What extinguishing agents actually stop battery re-ignition?

Agents that address re-ignition need to do more than suppress visible flames. They should provide sustained cooling, help insulate cells from one another, and limit the spread of heat and gas. No agent guarantees that re-ignition will not occur. Performance depends on access to the battery, the pack configuration, how the agent is delivered, and the available test evidence.

Each conventional agent has strengths and limits:

  • Water: provides effective cooling and is widely available. Its low viscosity means it drains from hot surfaces, which shortens contact time.
  • Foam: adheres better to surfaces. Many foams contain PFAS, which face increasing regulatory restriction in Europe, with a phase-out of PFAS-containing suppression agents expected under EU regulation by 2031.
  • Dry chemical powder: can knock down flames but provides little cooling and does not address the heat inside the battery.
  • CO2 and other gaseous agents: can displace oxygen around flames but provide limited cooling of the cells themselves.

Hydrogel by Anogas is designed for cooling and initial fire suppression. It is a water-based agent containing modified natural clay, and its viscosity rises when heated so that it keeps contact with hot surfaces. Anogas describes its action as sustained cooling, thermal isolation of adjacent cells, suppression and partial neutralisation of hazardous gases including hydrogen fluoride, stabilisation of reactive lithium ions by the clay particles, and continued cooling after visible flames have gone. How far this reaches inside an enclosed pack depends on access and delivery. An externally applied agent cannot be assumed to reach every internal cell or stop every internal reaction.

For longer-term containment of damaged or extinguished batteries, the relevant product is Hydrogel Shield, which is intended to help prevent re-ignition. Hydrogel SubZ is a frost-protected formulation for cold-temperature applications.

Hydrogel has been tested to KIWA NTA 8133 for lithium-ion battery fires. That result applies to the specific extinguisher model and test scope involved. It is not approval of every battery size or installation, and it is not approval of a complete marine battery installation. Hydrogel contains no intentionally added PFAS, which matters where PFAS regulation affects agent selection. That is a separate question from firefighting performance or marine approval.

Hydrogel is water-based and designed to be compatible with water-based suppression systems. Do not assume an existing sprinkler system works with it. Check compatibility, nozzle and discharge arrangement, agent quantity, coverage, operating temperature, and any required approvals first, with engineering input.

How do you safely handle a battery fire to minimise re-ignition risk?

Follow the emergency procedures that apply to your site and the battery involved. As general guidance, apply a cooling agent to the flames and gas-release points, keep cooling the pack surface once the flames are controlled, and monitor the battery after apparent extinguishment. A monitoring period of at least 20 minutes is a common minimum, but the right period depends on the battery and the conditions.

Sequence matters. Deal with visible flames first to prevent spread, then maintain a consistent cooling layer on the pack surface. Where the agent can reach the inside of the pack, it can help cool cells that may still be in thermal runaway. If internal components cannot be reached, applying more agent may not help. Stop, reassess, and consider whether specialist support is needed.

After the fire appears out, the work continues. Move the battery to a water-filled containment vessel if possible, or store it outdoors in a well-ventilated area away from combustible materials. Watch for new flames, hissing, or heat generation. Restrict access to the area while this continues. The commonly recommended minimum cooling period before disposal is 48 hours.

Operators need appropriate respiratory protection. Gases including hydrogen fluoride can continue to escape after flames are suppressed and are a serious inhalation hazard. Keep a safe distance and use suitable personal protective equipment at every stage.

Where battery fires are a recurring risk, fixed fire suppression systems designed for lithium-ion battery environments can give more consistent application than manual intervention alone. Assess the enclosure, battery configuration, and agent delivery before selecting one.

Which industries face the highest re-ignition risk from battery fires?

Re-ignition risk is highest where large numbers of lithium-ion batteries are stored, charged, or processed together. This includes electric vehicle facilities, energy storage installations, warehousing and logistics, recycling facilities, and the maritime sector. In these settings, the density of batteries raises both the likelihood and the consequences of re-ignition.

Warehousing and logistics operations face growing exposure as electric forklifts, e-bikes, and battery-powered delivery equipment become common. When batteries are stored or charged in large numbers in enclosed spaces, one thermal runaway event can spread across several units. Enclosed spaces also increase the hazard from gas accumulation.

Recycling facilities present a distinct challenge. Incoming batteries may be damaged, partially discharged, or in unknown condition, all of which increase thermal runaway risk. A battery that appears inert can still hold enough energy to ignite, and other combustible waste in the same facility adds to the hazard.

Energy storage systems used in renewable energy, grid stabilisation, and commercial buildings often use large-format packs, where propagation between cells can be hard to interrupt once it starts. Re-ignition in one module can develop into a much larger incident before it is detected.

Maritime environments add limited access, restricted ventilation, and the difficulty of delivering enough cooling agent to large battery systems in confined spaces. Handheld extinguishers suited to lithium-ion battery fires can give first responders an immediate suppression option while specialist help is arranged. They do not replace mandatory marine fire protection, and the standards involved are separate: battery-product standards, dangerous-goods transport rules, portable-extinguisher tests, flag-state requirements, class rules, and marine equipment approvals. Confirm the approval route with engineers and the relevant authority before changing any existing system.

Across all of these sectors, the point is the same: extinguishing visible flames does not remove re-ignition risk. The risk is reduced by sustained cooling, thermal isolation, and careful monitoring in the period after apparent extinguishment, matched to the battery configuration and the access available.

Gerelateerde artikelen

Harry Verbakel