Cooling capacity largely determines how quickly a fire is extinguished, because removing heat is the main way combustion is interrupted. When an extinguishing agent absorbs heat faster than the fire generates it, the reaction cannot sustain itself and the flames die back. The agent’s ability to stay in cooling contact over time matters just as much, especially where materials retain heat internally, as lithium-ion batteries do. The sections below cover each dimension of this relationship, from the physics of heat absorption to the performance demands of industrial fire suppression.
Why does cooling capacity determine how quickly a fire is extinguished?
Cooling capacity determines extinguishment speed because fire is a self-sustaining chemical reaction that needs heat to continue. When an agent absorbs heat from the combustion zone faster than the fire can regenerate it, the temperature falls below the ignition threshold and the flames cease. The higher the agent’s heat absorption rate, the sooner that threshold is reached.
The relationship is not a simple exchange of temperature. Suppression performance depends on how efficiently an agent carries thermal energy away from the fuel, and on how long it stays in contact with the hot surface while doing so. An agent that evaporates or runs off immediately delivers a brief cooling pulse, after which the surface can reheat and reignite. An agent that stays in contact sustains the cooling effect and drives the surface temperature progressively lower, which reduces the risk of reignition.
Water is the most widely used extinguishing agent because its heat of vaporisation, the energy absorbed as it turns from liquid to steam, is exceptionally high. However, water tends to run off vertical and irregular surfaces, which limits the duration of contact. In practice, cooling capacity is therefore not only a question of the agent’s thermal properties. It also depends on how well those properties are delivered to the fire and maintained there.
What factors affect the cooling capacity of a fire suppression agent?
Four main factors affect cooling capacity: the agent’s specific heat and heat of vaporisation, its viscosity and surface adhesion, the volume and rate of application, and how well it keeps contact with the burning surface under heat. Agents that perform well across all four tend to deliver better suppression.
Specific heat is the thermal energy a substance absorbs per unit of temperature rise. Heat of vaporisation is the additional energy absorbed when the substance changes from liquid to vapour. Water scores very well on both, which is why water-based agents dominate fire suppression. Raw thermal capacity is only part of the picture, though.
Viscosity and surface adhesion determine how long the agent stays on the fire source. A low-viscosity liquid drains quickly from hot surfaces, shortening the effective cooling time even when its thermal properties are excellent. An agent that thickens under heat and adheres to surfaces stays in contact longer, extracts more energy from the fuel and sustains the suppression effect.
Application rate also matters. Delivering a large volume quickly concentrates the cooling effect and can overwhelm the fire’s heat generation. In many real incidents, particularly industrial or battery-related ones, the geometry of the fire limits access. In those cases, adhesion and the ability to reach the heat source can matter more than volume.
How does cooling capacity differ between water, foam, and hydrogel agents?
Water, foam and hydrogel agents cool in different ways, so their suppression performance differs. Water has high raw heat absorption but poor surface adhesion. Foam adds a physical barrier and some adhesion, but many conventional formulations rely on PFAS, which raises environmental concerns. Hydrogel combines high water content with heat-responsive viscosity, which is intended to keep the agent in contact with hot surfaces for longer. How far that advantage extends depends on access, application method and the fire scenario.
Water
Water’s heat absorption is excellent, and it remains the baseline against which other agents are measured. Its limitations are physical rather than thermal. It flows off surfaces quickly, particularly vertical or angled ones, and it has no mechanism to hold a cooling layer once the initial pulse has passed. Large volumes are often needed to compensate, which increases runoff and the risk of secondary contamination.
Conventional foam
Aqueous film-forming foams improve on water by forming a film that separates fuel from oxygen and reduces surface runoff. However, many conventional foam formulations contain PFAS, per- and polyfluoroalkyl substances, which are persistent environmental contaminants. European regulation under Regulation (EU) 2025/1988 is phasing out PFAS-containing extinguishing agents, with a complete ban expected by 2031. This is pushing the industry towards alternatives that can match suppression performance without the environmental liability.
Hydrogel
Hydrogel is a water-based agent containing modified natural clay. It is relatively low in viscosity at ambient temperature and thickens when exposed to heat, so it is intended to adhere to hot surfaces rather than drain away. The hotter the surface, the more firmly the gel is designed to hold, which helps maintain cooling contact. Anogas’s Hydrogel technology applies this mechanism across multiple fire classes. It is designed for sustained heat extraction, is PFAS-free and has a carbon footprint of less than 0.7%. Its effectiveness in a given scenario still depends on access, agent delivery and the configuration of the fire source.
Why is cooling capacity especially critical for lithium-ion battery fires?
Cooling capacity is especially critical for lithium-ion battery fires because the energy driving the incident comes from inside the cells, not only from an external fuel source. Thermal runaway, the self-accelerating chain reaction triggered by overheating, mechanical damage or electrical fault, can continue after visible flames appear to have been suppressed. Extinguishing flames is therefore not the same as stabilising the battery. Sustained cooling is needed to slow the internal heating, and its effect depends on how well the agent can reach the affected cells.
During thermal runaway, internal materials decompose and release flammable gases, including hydrogen and methane, as well as toxic hydrogen fluoride. Heat from one failing cell transfers to neighbouring cells and can trigger a cascade of failures. An agent that delivers a brief cooling pulse and then runs off cannot address this internal heat generation. The battery can reheat and the cycle can restart.
Effective suppression therefore calls for an agent that holds a cooling layer on battery surfaces and keeps lowering temperature after the flames are gone. An externally applied agent will not necessarily reach cells inside an enclosed pack, so performance depends on access, battery configuration and how the agent is delivered. This is why thermal runaway blockers designed for battery incidents treat suppression as a multi-stage process rather than a single intervention. The aim is not only to put out the flames but to reduce temperature over an extended period and lower the risk of reignition.
The post-fire period needs the same attention. After a battery fire appears stable, residual heat, gas release and chemical activity can persist within the cells. Monitoring periods, cooling and isolation times vary with the battery, the incident and the guidance applied. As a general reference, industry guidance often recommends observing the unit for at least 20 minutes after extinguishment and isolating it for at least 48 hours before disposal. Treat these figures as a starting point, confirm them against the applicable guidance and do not assume the battery is safe to reuse, store or transport.
How does surface adhesion improve cooling efficiency in fire suppression?
Surface adhesion improves cooling efficiency by extending the contact time between the agent and the hot surface, so more heat is extracted per unit of agent. An agent that clings to a burning surface delivers sustained heat absorption instead of a brief pulse. This can reduce the volume needed and lower the risk of reignition.
The practical implications cover both performance and resource use. When an agent drains away quickly, the operator must apply more to maintain the cooling effect, which increases runoff, contamination risk and cost. When an agent adheres, each application extracts more energy from the fuel before the material disperses.
For battery fires, adhesion also helps the agent stay in contact with the outer casing of a pack while internal temperatures remain high. This surface layer can act as a thermal barrier, slowing heat transfer to adjacent cells and reducing the likelihood of cascading failure. Whether it does so depends on the pack design and how much of the surface the agent can reach. In some configurations, a gel-forming agent can also expand on application, improving coverage and contact on irregular geometries. That can help with energy storage systems and battery packs where cell geometry is complex.
Adhesion can also support safer application distances. An agent that keeps its cooling layer after contact may allow operators to apply it from further away, reducing exposure to hazardous gases and heat. Anogas’s Hydrogel has been tested to KIWA NTA 8133 for lithium-ion battery fire applications and is supplied as a ready-to-use premix, which supports consistent application. Teams should verify the scope of that test, including the extinguisher model and battery type covered, before applying the result to a specific installation.
What cooling performance should fire suppression agents meet for industrial use?
For industrial use, agents should absorb heat rapidly on contact, adhere to hot surfaces, suit the fire classes present in the facility and remain environmentally safe during and after application. Where lithium-ion batteries or energy storage systems are involved, the agent must also address reignition risk and thermal propagation, not only visible flames.
Industrial environments carry fire risks that differ from residential or commercial settings. Warehouses holding large quantities of lithium-ion batteries, vessels with energy storage systems, recycling facilities processing electronic waste and plants with high-voltage equipment all face scenarios in which a single agent or system may not be enough. High energy density, enclosed geometries and the potential for cascading failure call for both strong thermal performance and chemical stability. Water, dry chemical, CO2 and foam each have a role, and each has limits that depend on the hazard.
From a regulatory standpoint, the move away from PFAS-containing agents is accelerating. Facilities that rely on PFAS-based foams will need to transition to compliant alternatives before the 2031 deadline under European law. Selecting a high-performance, PFAS-free agent is therefore a compliance question as well as a safety one. PFAS-free status does not by itself show that an agent is effective, environmentally harmless or approved for a given application.
When selecting an agent, assess the whole firefighting setup rather than the agent alone. Verify:
- access to the battery and the design of the enclosure;
- the agent quantity needed for the scenario;
- the nozzle and discharge arrangement, and the coverage it achieves;
- operating temperature limits and compatibility with existing equipment;
- the test evidence and approvals that apply to the installation.
Do not assume that an existing sprinkler or fixed suppression system will work with Hydrogel. Changes to installed systems, particularly in marine settings, need engineering assessment and the relevant approvals. For facilities evaluating fire suppression systems for battery or industrial applications, confirm these points with the supplier and the approving authority before committing to a design.
The same criteria apply at a smaller scale to handheld extinguishers used in first response. Agents in portable extinguishers must cool effectively on contact, stay on the fire source long enough to reduce the risk of reignition, and be safe for the operator to deploy near burning batteries or industrial materials. Confirm which extinguisher model, test and scope a certificate covers. A portable-extinguisher test result does not extend to every battery size or to a complete installed system.


